Autel Maxosys Pro 9089 ECU Programming Function:
AUTEL MAXISYS Pro itself has already supported ECU programming function for BENZ and BMW cars, if you need to get support for more car models,
you must use J2534 device along with OEM software to implement this function. J2534 DEVICE can not only use with AUTEL MAXISYS Pro , but also can work on other OEM software.
Autel MS908P Function Descriptions DTC & FFD
When this function is selected, the screen displays a list of Stored Codes and Pending Codes. When the Freeze Frame data of certain DTCs are available
for viewing, a snowflake button will display on the right side of the DTC item.The Erase Codes function can be applied by tapping the functional button at
the lower bottom of the screen.
Stored Codes
Stored codes are the current emission related DTCs from the ECM of the vehicle. OBDII/EOBD Codes have a priority according to their emission severity, with
higher priority codes overwriting lower priority codes. The priority of the code determines the illumination of the MIL and the codeserase
procedure. Manufacturers rank codesdifferently, so expect to seedifferences between makes.
Pending Codes
These are codes whose setting conditions were met during the last drive cycle, but need to be met on two or more consecutive drive cycles before
the DTC actually sets. The intended use of this service is to assist the service technician after a vehicle repair and after clearing
diagnostic information, by reporting test results after a single driving cycle.
a)If a test failed during the driving cycle, the DTC associated with that test is reported.If the pending fault does not occur again within 40 to
80 warm-up cycles, the fault is automatically cleared from memory.
b)Test results reported by this service do not necessarily indicate afaulty component or system. If test results indicate another failure
after additional driving, then a DTC is set to indicate a faulty component or system, and the MIL is illuminated.
Freeze Frame
In most cases the stored frame is the last DTC thatoccurred.Certain DTCs, those that have a greater impact on vehicle emission, have a
higher priority. In these cases, the highest priority DTC is the one for which the freeze frame records are retained. Freeze frame data includes
a “snapshot”of critical parameter values at the time the DTC is set.
Erase Codes
This option is used to clear all emission related diagnostic data such as,DTCs,freeze frame data and manufacturer specific enhanced data from
the vehicle’s ECM, and resets the I/M Readiness Monitor Status for allvehicle monitors to Not Ready or Not Complete status.A confirmation
screen displays when the clear codes option is selected toprevent accidental loss of data. Select Yes on the confirmation screen to continue, or
No to exit.
I/M Readiness
This function is used to check the readiness of the monitoring system. It is an excellent function to use prior to having a vehicle inspected for
compliance to a state emissions program. Selecting I/M Readiness opens a submenu with two choices:
Since DTCs Cleared–displays the status of monitors since the last timethe DTCs are erased.
This Driving Cycle–displays the status of monitors since the beginningof the current drive cycle.
Live Data
This function displays the real time PID data from ECU. Displayed data includes analog inputs and outputs, digital inputs and outputs,
and systemstatus information broadcast on the vehicle data stream.
O2 Sensor Monitor
This option allows retrieval and viewing of O2 sensor monitor test results for the most recently performed tests from the vehicle’s on-board computer.
The O2 Sensor Monitor test function is not supported by vehicles whichcommunicate using a controller area network (CAN). For O2 Sensor Monitor
tests results of CAN-equipped vehicles, refer to On-Board Monitor
On-Board Monitor
This option allows you to view the results of On-Board Monitor tests. The tests are useful after servicing or after erasing a vehicle’s control module memory.
Component Test
This service enables bi-directional control of the ECM so that the diagnostictool is able to transmit control commands to operate the
vehicle systems. Thisfunction is useful in determining how well the ECM responds to a command.
Vehicle Information
The option displays the vehicleidentification number (VIN), the calibrationidentification, and the calibration verification number (CVN), and
other information of the test vehicle.
Vehicle Status
This item is used to check the current condition of the vehicle, including communication protocols of OBD II modules, retrieved codes
amount, status of the Malfunction Indicator Light (MIL), and other additional information may be displayed.
Service
The Service section is specially designed to provide you quick access to the vehicle systems for various scheduled service and maintenance performances.
The typical service operation screen is a series of menu driven executive commands.By following the on-screen instructions to select appropriate
execution options, enter correct valuesor data, and perform necessary actions, the system will guide you through the complete performance for
various service operations.
The most commonly performed service functions include:
Oil Reset Service
TPMS Programming Service
EPB Service
ABS/SRS Services
SAS Calibration Service
DPF Regeneration Service
This section describes the main functions for vehicle service:
Oil Reset Service
This function allows you to perform reset for the Engine Oil Life system, which calculates an optimal oil life change interval depend on the
vehicle driving conditions and climate. The Oil Life Reminder must be reset every time the oil is changed, so the system can calculate when
the next oil change is required.
Tire Pressure Monitor System (TPMS) Service
This function allows you to quickly look up the tire sensor IDs from the vehicle's ECU,as well as to perform TPMS
programming and reset proceduresafter tire sensors are replaced.
Electric Parking Brake (EPB) Service
This function has a multitude of usages to maintain the electronic braking system safely and effectively.The applications include
deactivating and activating the brake control system, assisting with brake fluid control, opening and closing brake pads, ands etting brakes
after disc or pad replacement, etc.
ABS/SRS Services
This function allows you to perform various bi-directional tests to check the operating conditions of both the Anti-lock Braking System
and the Supplemental Restraint System, such as Automated Bleeding,Pump Motor Test,and checking Module information, etc.
Steering Angle Sensor (SAS) Service
This service function allow you to perform calibration for the Steering Angle Sensor, which permanently stores the current
steering wheel position as the straight-ahead position in the steering angle sensor EEPROM. On successful completion of the calibration,
the steering angle sensor fault memory is automatically cleared.
DPF Regeneration Service
The Diesel Particulate Filter service function performs the regeneration procedure which is the DPF cleaning operation to clear
the blockage through continuous burning of the particulate matter captured in the DPF filter.If the DPF light on the vehicle comes
on and you successfully complete a DPF regeneration cycle, you will notice that the DPF light will automatically turn off.
Operating System | AndroidTM 4.0, Ice Cream Sandwich | |
Processor | Samsung Exynos Quad-Core Processor 1.4GHz | |
Memory | 2GB RAM & 32GB On-board Memory | |
Display | 9.7 inch LED capacitive touch screen with 1024x768P resolution | |
Connectivity | Ethernet: RJ45 Ethernet Connection,Cellular: 3G/4G module: WCDMA | |
Camera (rear) | Rear-facing, 5.0 Mexgapixel, AF with Flashlight | |
Sensors | Gravity Accelerometer, Ambient Light Sensor (ALS) | |
Audio Input/Output | Microphone, Dual Speakers, 4-Band 3.5 mm stereotype/standard headset jack | |
Power and Battery | 11000 mAh 3.7 V lithium-polymer battery, Charging via 12 V vehicle power | |
Input Voltage | 12 V (9-24 V) | |
Power Consumption | 6.5 W | |
Operating Temperature | -10 to 55 ℃ (14 to 131 ℉) | |
Storage Temperature | -20 to 70 ℃ (-4 to 158 ℉) | |
Housing | Strong plastic housing with protective rubber boot | |
Dimensions (W x H x D) | 300 mm (11.81”) x 220 mm (8.66”) x 50 mm (1.97”) | |
Weight | NW: 1.42 kg (3.13 lb), MaxiSys GW: 8.655 kg (19.08 lb) / MaxiSys Pro GW: 8.052 kg (17.75 lb) |
Contact Us
Shipping Warranty:
1) EU Warehouse Shipping: 3-5 working days with No Tax. We have stock in our Czech warehouse for most items. All Items titled "EU Ship" are ship from our Czech warehouse.
2) Yodel Virtual warehouse Shipping: 6-8 days with No Tax for EU customers.
3) Yanwen Express: 8-12 working days. No Tax for European Countries.The tax was pre-paid by us, when package reached, there's no tax no extra fee for customers.
(Due to high custom tax in European Countries,Like Germany, Greece,Romania,Sweden,France,etc, we will use Yanwen express as first option, if you need faster DHL shipment,please contact us ,thank you)
4) DHL Shipping: 5-7 working days. For the items have no stock in EU warehouse, we will ship it by DHL. We will declare a lower price on the invoice to help your clearance.
5) 4PX Postal Service: 7-10 working days. For the products mentioned"Standard Flat Rate Shipping Service" we will send via postal service
MaxiSYS Pro MS908P update tool download
Autel MaxiSys MS908 Pro Latest Software Version and Function List
Num | Vehicle Type Image | Vehicle Type Name | Respective Category | Latest Version | Download |
1 | BUGATTI | European | V2.00 | Download | |
2 | Porsche | European | V2.00 | Download | |
3 | BENTLEY | European | V2.00 | Download | |
4 | MAYBACH | European | V3.00 | Download | |
5 | VAUXHALL | European | V1.51 | Download | |
6 | ALFA ROMEO | European | V2.10 | Download | |
7 | LANCIA | European | V2.10 | Download | |
8 | ABARTH | European | V2.10 | Download | |
9 | FIAT | European | V2.10 | Download | |
10 | SAAB | European | V1.03 | Download | |
11 | SPRINTER | European | V1.30 | Download | |
12 | KIA | Asian | V2.01 | Download | |
13 | DAEWOO | Asian | V1.02 | Download | |
14 | ISUZU | Asian | V1.02 | Download | |
15 | JAGUAR | European | V2.10 | Download | |
16 | CITROEN | European | V2.00 | Download | |
17 | SMART | European | V1.20 | Download | |
18 | TOYOTA | Asian | V1.70 | Download | |
19 | SUBARU | Asian | V1.50 | Download | |
20 | SCION | Asian | V1.70 | Download | |
21 | NISSAN | Asian | V2.20 | Download | |
22 | MITSUBISHI | Asian | V2.10 | Download | |
23 | LEXUS | Asian | V1.70 | Download | |
24 | INFINITI | Asian | V2.20 | Download | |
25 | HYUNDAI | Asian | V2.01 | Download | |
27 | HONDA | Asian | V3.00 | Download | |
28 | ACURA | Asian | V3.00 | Download | |
29 | MAZDA | Asian | V3.00 | Download | |
30 | VOLVO | European | V1.30 | Download | |
31 | VW | European | V2.00 | Download | |
32 | SKODA | European | V2.00 | Download | |
33 | SEAT | European | V2.00 | Download | |
34 | RENAULT | European | V2.60 | Download | |
35 | PEUGEOT | European | V2.00 | Download | |
36 | OPEL | European | V1.51 | Download | |
37 | MINI | European | V2.00 | Download | |
38 | LAND ROVER | European | V2.10 | Download | |
39 | EU FORD | European | V3.00 | Download | |
40 | DACIA | European | V2.60 | Download | |
41 | BMW | European | V2.00 | Download | |
42 | BENZ | European | V3.00 | Download | |
43 | AUDI | European | V2.00 | Download | |
44 | GM | American | V3.00 | Download | |
45 | CHRYSLER | American | V2.10 | Download | |
46 | FORD | American | V3.00 | Download |
Customer share: